Home / Shop / Starlink Wall & Eave Bracket
Starlink Wall & Eave Bracket
For steep roofs, or anywhere you'd rather not cut into the roof for your Starlink.
$59.39
Secure checkout via Payhip · Free shipping on every order — no minimum · 30-day returns
Two options, one listing. This Payhip listing covers both Wall Mount and Roof Mount. Checkout is already set to Wall Mount — there is nothing to choose.
Fits: Standard (Gen 3 / V3 / Standard 4) and Mini via the 1.5" pipe thread.
- ✓No pipe adapter to buy — the 1.5 inch pipe thread is built into the bracket
- ✓Keeps the dish away from roof traffic, snow and ice
- ✓Loads spread across a 6-point mounting plate
- ✓Two anchor types included: masonry and timber
- ✓Slim profile — barely visible from the street
Specs
| Compatible dishes | Standard (Gen 3 / V3 / Standard 4), Mini |
|---|---|
| Mast interface | 1.5 inch pipe thread |
| Pipe adapter | Not required — the thread is built in |
| Anchors | 6 points — masonry + timber anchors included |
| Reach | 11 in from the wall face |
| Finish | Matte black powder coat |
| Mounts to | Brick, stucco, timber, fascia, gable end |
| In the box | Bracket, plate, anchors, printed instructions |
Fitment & install
Full step-by-step instructions ship in the box. If anything is unclear, email us a photo of your setup and we'll walk you through it.
- ✓Mark the plate, check the angle, then anchor all six points.
- ✓Typical install time: 30–45 minutes.
- ✓Seal the anchors if you mount onto brick or stucco.
Compatible with
| Model | Compatible | Notes |
|---|---|---|
| Starlink Standard (Gen 3 / V3 / Standard 4) | Yes | Mast uses the same 1.5" pipe thread the dish ships with. |
| Starlink Mini | Yes | Same thread — the Mini screws straight on. |
| Starlink Gen 2 (rectangular) | No | Different mast fitting to the current thread. |
| Starlink Gen 1 (original round dish) | No | Predates the 1.5" pipe thread. |
“Compatible with” means the part physically fits and works with that device. Zatelitount is an independent maker of installation hardware — not affiliated with, endorsed by, or an official supplier to SpaceX or Starlink. See the full compatibility page, or run the Mount Finder if you are still deciding.
Before you order
Why choose a wall bracket over a roof mount?
Two reasons: you keep the roof membrane intact, and you get the dish away from snow, ice and roof traffic. On steep roofs it's also far safer to install. Both fit the same Starlink dishes.
Is professional installation required for this Starlink wall bracket?
No. It's a six-point anchor job with basic tools — most people finish in 30–45 minutes. Seal the anchors if you mount onto brick or stucco, and email us a photo if you're unsure where to place the plate.
Does this Starlink wall bracket survive strong wind?
Yes. The load spreads across a six-point plate and the mast reaches 11 inches from the wall, so the dish stays put in normal weather. For hurricane-grade exposure, message us first and we'll advise.
Do I need to buy a pipe adapter as well?
No. The 1.5 inch pipe thread your dish mounts to is built into the bracket, so the official pipe adapter isn't needed — nothing else is required to fit the dish.
Will it clear the eaves?
It reaches 11 inches from the wall face, which clears most standard overhangs. If your eaves are deep, measure first or ask us.
Do I have to pick an option at checkout?
No — checkout is already set to "Wall Mount" for you. That Payhip listing carries both the roof mount and this wall bracket, so if you somehow see the roof mount there, email us before you pay and we'll sort it out.
What does shipping cost?
Nothing — every US order ships free, no minimum.
Related reading
This is the option for a roof you would rather not touch. See wall versus eave: which side of the house gets a clear view, or all four ways to mount without drilling.
Others in the range
Starlink Roof Mount Kit
Low-profile Starlink roof mount that holds its position through high wind, snow load and heavy rain.
Adjustable Heavy-Duty Starlink Tripod Stand
A freestanding, height-adjustable Starlink stand — set it down where the sky is clear and take it with you when you go.
Starlink Gen 3 Router Wall Mounts
A slim wall bracket for the Starlink Gen 3 router, so the power lead and cables stop living on the floor.